News
Home » News » Lawn mower » Remote Control Mower Work Rate: Cutting Width, Travel Speed, and Turning Time

Remote Control Mower Work Rate: Cutting Width, Travel Speed, and Turning Time

Views: 0     Author: Site Editor     Publish Time: 2026-11-17      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button

Two sites can have the same mowing area and take very different amounts of time. Long, open passes let a remote-control lawn mower keep cutting. Short passes around trees or posts mean more turns and time lining up for the next strip.

To estimate a job, start with the width of fresh grass cut on each pass and the speed you can maintain while mowing. Then add the time you spend turning, repositioning, and working around obstacles.

Quick Answer

  • Subtract pass overlap from the nominal cutting width to estimate the effective cutting width.

  • Time a straight pass while the mower is cutting representative grass. Use that speed in your estimate.

  • Add turn and repositioning time to straight cutting time. Divide the finished area by the total time to find the job’s work rate.

Measure the Effective Cutting Width

The nominal cutting width gives you a starting point. GRANDEMAC’s remote-control lawn mower has a 520 mm cutting width. The GRANDEMAC 550A/550B hybrid crawler remote-control mower has a 550 mm cutting width.

If a 550 mm mower overlaps the previous pass by 50 mm, each new pass adds about 500 mm of fresh cut. Measure the spacing between adjacent passes on a representative test strip. If you need more overlap around curves, estimate those sections separately.

Time the Mower While It Is Cutting

Mark a straight section in grass that represents the job. Bring the mower to a steady cutting pace before the start marker. Time several passes, then divide the total distance in meters by the total time in seconds. Multiply by 3.6 to get kilometers per hour.

For example, a 40 m pass in 60 seconds gives a cutting speed of 2.4 km/h. Use a pace that leaves the finish you need. Record separate speeds if an open lawn and a dense orchard block require different passes.

Count Turns, Obstacles, and Stops

Time a few typical turns from the end of one pass to the start of the next. Multiply the average time by the expected number of turns. Record extra time for detours around trees and for repositioning between sections.

Use a clear start and finish point for the estimate. For an on-site mowing rate, include turns, repositioning, and stops during the block. For a crew schedule, add any setup, refueling, or charging time that falls outside that window.

Calculate the Remote Control Mower Work Rate

Multiply the effective cutting width in meters by the cutting speed in kilometers per hour and by 1,000. This gives the area covered in an hour of straight cutting. Divide the area by that rate to estimate straight cutting time.

Then add non-cutting time. Divide the finished area in square meters by the total time in hours to estimate the work rate for the whole block. Count each piece of ground once, even if the mower crosses it again.

Worked Example for a 900 m² Block

Input or result

Example

Nominal cutting width

0.55 m

Pass overlap

0.05 m

Effective cutting width

0.50 m

Cutting speed

2.4 km/h

Straight cutting rate

1,200 m²/h

Straight cutting time for 900 m²

45 min

Turning time

10 min

Extra repositioning and detours

5 min

Total mowing time

60 min

Work rate for the block

900 m²/h

This example uses assumed overlap, speed, and timing. To check your estimate, time a complete block and divide its finished area by the elapsed time. That timed result already includes any overlaps, turns, and stops within the test.

Compare Mowers on the Same Route

When comparing intelligent lawn mower options, use the same test area, grass conditions, and target finish. Record the effective width and timed cutting speed for each candidate. Compare their full-block times, including the time spent turning and lining up.

If your site includes both open ground and short rows, estimate each zone separately. Add their mowing times to plan the job. A timed trial in the more demanding zone gives you a better basis for scheduling that part of the site.

Conclusion

A useful work rate reflects the fresh width cut, the speed your crew can maintain, and the time lost between passes. Time one representative block before using the estimate for a larger site. Keep those measurements so you can compare equipment or plan the next visit.

Planning a Mower Trial for Your Site?

Share your mowing area, typical pass length, and main obstacles. Ask GRANDEMAC about a remote-control mower for your route.

Frequently Asked Questions

How Do I Measure a Remote-Control Lawn Mower’s Work Rate?

Time the mower from the first cut to the last cut on a measured block. Divide the finished area by elapsed hours. Record any unusual delays so you can interpret the result later.

Does a Wider Remote-Control Lawn Mower Always Finish Faster?

A wider deck can cover more ground per pass at the same speed. On a tight route, compare the usable width and the full-block time, including any extra repositioning.

Can I Use a Remote-Control Lawn Mower’s Top Speed to Estimate Output?

Use the speed you can maintain while cutting to the required finish. A timed pass through typical grass gives you a figure for your job.

What If Some Grass Needs a Second Pass?

Count the area once and include the extra cutting time. If second passes are common in one zone, give that zone a separate time estimate.

Should Charging Time Count Toward Mower Work Rate?

Include charging if it interrupts the block you are timing. For a full-day schedule, also count any charging that delays the next block.

  +8618921887735
 +86-18921887735 / +86-13365182967
 No.66 Hexin Road, Yandu District, Yancheng Jiangsu China

Quick Links

Product Category

Send Us A Message
Copyright © 2026 Jiangsu Grande Machinery Manufacturing Co., Ltd. All rights reserved. Sitemap |  Privacy Policy    苏ICP备2023030502号-2